Correlated courses in woodwork and mechanical drawing
Ira Samuel Griffith

THE CLASSIC COLLECTION · 1916
"Carpentry" by Ira Samuel Griffith is a practical guide on the fundamentals of carpentry written in the early 20th century. The text serves as an elementary treatise intended for apprentices, vocational and trade school students, highlighting essential techniques and principles of carpentry, with a focus on roof framing and structural integrity. At the start of "Carpentry," the author introduces the importance of foundational work in carpentry, emphasizing the role of carpenters in laying out foundations alongside masons. Griffith discusses the tools required for accurate measurements, such as the builder's transit and the Y-level, detailing how to properly establish a building site's grade line. He outlines the processes for excavating foundations, constructing footings, and selecting appropriate materials, providing a thorough overview of foundational principles essential for successful carpentry projects.
Introduction adapted from the source catalogue; source summaries may be automatically generated.
Free to read · English · 37,365 words · No account needed
MAKE TIME FOR A GOOD BOOK
On by default. Untick to stop anonymous reading totals. Each page counts after 10 seconds in view. How this works.
Anonymous counting is on unless you have switched it off.
Rule: (1) Search the body of the table for the functional values next above and next below that given. (2) Find the difference between these functional values. This difference is for an interval of 1 degree or 60 minutes. (3) Find the difference between the given functional value and that of the lower angle of the two used above. (4) Express this last difference as the numerator of a fraction whose denominator is the first difference found, or the difference for the interval of 1 degree. This gives the fractional part of 1 degree or 60 minutes which the second difference is. (5) Express this difference in minutes and add if the function be a sine or tangent, and substract if a cosine or cotangent to the number of degrees representing the angle whose function was the lower of the two functions found given in the table.
================================================================ .0156 | 1/64 || .2656 | 17/64 || .5156 | 33/64 || .7656 | 49/64 .0312 | 1/32 || .5312 | 9/32 || .2812 | 17/32 || .7812 | 25/32 .0468 | 3/64 || .2968 | 19/64 || .5468 | 35/64 || .7968 | 51/64 .0625 | 1/64 || .3125 | 5/16 || .5625 | 9/16 || .8125 | 13/16 .0781 | 5/64 || .3281 | 21/64 || .5781 | 37/64 || .8281 | 53/64 .0937 | 3/32 || .3437 | 11/32 || .5937 | 19/32 || .8437 | 27/32 .1093 | 7/64 || .3593 | 23/64 || .6093 | 39/64 || .8593 | 55/64 .125 | 1/8 || .375 | 3/8 || .625 | 5/8 || .875 | 7/8 .1406 | 9/64 || .3906 | 25/64 || .6406 | 41/64 || .8906 | 57/64 .1562 | 5/32 || .4062 | 13/32 || .6562 | 21/32 || .9062 | 29/32 .1718 | 11/64 || .4218 | 27/64 || .6718 | 43/64 || .9218 | 59/64 .1875 | 3/16 || .4375 | 7/16 || .6875 | 11/16 || .9375 | 15/16 .2031 | 13/64 || .4531 | 29/64 || .7031 | 45/64 || .9531 | 61/64 .2187 | 7/32 || .4687 | 15/32 || .7187 | 23/32 || .9687 | 31/32 .2343 | 15/64 || .4843 | 31/64 || .7343 | 47/64 || .9843 | 63/64 .250 | 1/4 || .500 | 1/2 || .750 | 3/4 || 1.000 | 1 ================================================================
Where rafter lengths are determined by multiplying unit lengths by the run, the answer will almost invariably result in a decimal. Such decimal values may be readily translated into fractional forms by means of the accompanying table.
Example: A roof of ⅓ pitch has a common rafter run of 14';
find the length of common rafter.
Answer: 14 × 14.42" = 201.88" or 16.82'. By the table, .82 = 53/64. A carpenter, however, would not care for such accuracy; the nearest 1/16" or even ⅛" would be sufficient.
The difference between consecutive sizes is .01316".
=================================================================== No. of | Size of || No. of | Size of || No. of | Size of Screw | Number in || Screw | Number in || Screw | Number in Gage | Decimals || Gage | Decimals || Gage | Decimals --------+------------++--------+------------++--------+------------ 000 | .03152 || 16 | .26840 || 34 | .50528 00 | .04486 || 17 | .28156 || 35 | .51844 0 | .05784 || 18 | .29472 || 36 | .53160 1 | .07100 || 19 | .30788 || 37 | .54476 2 | .08416 || 20 | .32104 || 38 | .55792 3 | .09732 || 21 | .33420 || 39 | .57108 4 | .11048 || 22 | .34736 || 40 | .58424 5 | .12364 || 23 | .36052 || 41 | .59740 6 | .13680 || 24 | .37368 || 42 | .61056 7 | .14996 || 25 | .38864 || 43 | .62372 8 | .16312 || 26 | .40000 || 44 | .63688 9 | .17628 || 27 | .41316 || 45 | .65004 10 | .18944 || 28 | .42632 || 46 | .66320 11 | .20260 || 29 | .43948 || 47 | .67636 12 | .21576 || 30 | .45264 || 48 | .68952 13 | .22892 || 31 | .46580 || 49 | .70268 14 | .24208 || 32 | .47896 || 50 | .71584 15 | .25524 || 33 | .49212 || | --------+------------++--------+------------++--------+------------
Frequently the carpenter wishes to know the diameter of hole necessary to receive the shank of a screw of a certain gage. Should a screw gage be accessible, he may readily determine this. Should no gage be at hand, he may determine the size of hole by consulting the accompanying table of Wood and Machine Screw Sizes.
Example: What size bit must be selected to bore a hole for a No. 10 screw. By the table, a No. 10 screw is .18944" in diameter. By the table of Fractional Equivalents for Decimal Values it will be seen that a 3/16" bit must be used. The test for gage of screw is always made over the shank just below the head.
================================================================ Size |LENGTH|COMMON|CASING|FINISH|CLINCH|FENCE | FINE | GAL. | INS. | | | | | | | SHINGLE -----+------+------+------+------+------+------+------+--------- ¾ | ¾ | | | | | | | ⅞ | ⅞ | | | | | | | 2d | 1 | 900 | | | | | 1440 | 3d | 1¼ | 615 | | | | | 810 | 568 4d | 1½ | 322 | 473 | 584 | | | 250 | 5d | 1¾ | 254 | | | | | | 6d | 2 | 200 | 180 | 300 | 157 | 114 | | 7d | 2¼ | 154 | | | | | | 8d | 2½ | 106 | 112 | 190 | 99 | 74 | | 9d | 2¾ | 85 | | | | | | 10d | 3 | 74 | 90 | 134 | 69 | 42 | | 12d | 3¼ | 57 | | | | | | 16d | 3½ | 46 | .| | | | | 20d | 4 | 29 | | | | | | 30d | 4½ | 23 | | | | | | 40d | 5 | 17 | | | | | | 50d | 5½ | 14 | | | | | | 60d | 6 | 11 | | | | | | -----+------+------+------+------+------+------+------+------
Your reading position is saved on this browser. Take it to another device with a library code. Reading pages adapt to text, rather than matching a printed edition.
BEHIND THE BOOK
This eBook is for the use of anyone anywhere in the United States and most other parts of the world at no cost and with almost no restrictions whatsoever. You may copy it, give it away or re-use it under the terms of the Project Gutenberg License included with this eBook or online at www.gutenberg.org. If you are not located in the United States, you will have to check the laws of the country where you are located before using this eBook. Read the source licence.
The original source file, including credits and licence, is retained by this library. Request an original-format copy at no charge. Please include the book title and Project Gutenberg identifier #70226.
KEEP YOUR CURIOSITY GOING

Charles G. (Charles Griffith) Ross
Hannah Webster Foster

Emily Lawless
Edwin Hamlin Carr

Charles De Lano Hine
Andrew Ure